4WD BALL JOINT KIT

Complete set of upper and lower ball joints w/ seals and o-rings 99-04 F-SERIES 4x4

Kit contains:

2-K80026 upper greasable ball joints Moog Brand

2-K8607T lower greasable ball joints Moog Brand

2-F81Z 4A322AA Yellow O-rings between the hub and knuckle

2-F81Z 3254CB Hub seals

2-F81Z 1S175HCA Axle seals

Moog brand is superior to the OEM Ford balljoints due to the fact that they come with a grease zerk. This is enables you to grease them and prolong the life versus the OEM ones which are a sealed unit and do not allow you to grease them.

Click here for a detailed writeup on Ball Joint replacement

Complete Set of Trailer Tow Mirrors with Lights

as used on 03 Model Year and Up

Parts included are:

2 Mirrors Heated with Power 

2 Mirror Cover which include the Light Modules (PLEASE Specify if you would like Black Grained Finish or Paint to match Body Color Finish)

2 connectors to convert round plug to rectangular (Not all applications will need these but we include them in all kits "just in case")

This is not a 100 % bolt on upgrade on all vehicles and may require addtional parts to make it fully operational.  We will be happy to try and answer any questions we can.

Click here for a typical installation of the Trailer Tow Mirrors.

You will recieve the all of the following. A complete kit to add the Factory Upfitter bank of switches to run whatever accessories you like onto your 2005 or newer Superduty.

1- bank of On/Off switches fits into existing panel on dash no cutting or drilling required.

1- Complete harnes with plugs to plug right into the fuse panel, you also get all of the necessary relays and fuses installed in the block which is integrated into the harness.

1- Storage bin to fill the gap left after installing switches on some applications.

Click here to see an installation of our Upfitter switch kit.

Kit includes 8 Motorcraft Glow Plugs (12A342), 2 Under Valve Cover Harnesses (9D930), and 2 Valve Cover Gaskets (6584). Everything you need to replace the Glow Plugs all in one easy package!

This a comprehensive kit that will allow you to have everything you need to replace both front hub bearings and all ball joints both the upper and lower all in one package shipped to your door.  When ordering this kit we will need to know the last 8 of your VIN so we can determine the application of the hub bearing.  Please be aware that if you have an Early build 1999 model to use these Hub Bearings it will require you to change the rotors to the later style. We can either provide you the rotors or to save on shipping we can give several different aftermarket part numbers that can obtain locally. You will recieve the following:

Moog Brand Greaseable Ball Joints

2-K80026 upper greasable ball joints

2-K8607T lower.greasable ball joints

2-F81Z4A322AA Yellow Orings between the hub and knuckle

2-F81Z3254CB Hub seals

2-F81Z1S175HCA Axle seals

8-F81Z1107AA Studs to connect hub bearing to knuckle

8-F81Z1120AA Nuts for above studs

2-Timken Hub Beaing Assy

These include all wheel studs and ABS sensors if applicable.  Part Number varies dependent on application.  Please provide the last 8 Digits of you Vehicle Identification Numer (VIN) so we can determine the correct ones for your truck.

 As you can see this is everything in one box and ready to go so you don't have to make the extra trips after a seal or stud half way into the repair.  All parts meet or exceed OEM standards at a fraction of the cost.

Kit includes 8 Motorcraft Glow Plugs (12A342), 4 Under Valve Cover Harnesses (9D930), and 2 Valve Cover Gaskets (6584). Everything you need to replace the Glow Plugs all in one easy package!

Our own custom kit we have put together using all OEM parts to completely reseal your leaky oil cooler.

Our kit contains EVERYTHING you will need to remove and replace both

gaskets and all 4 o-rings.

Kit contents

2-1C3Z6C610BA Thick Green O-rings

2-1C3Z6K649BA Thin Blue O-rings

1-F7TZ6A636AAA Gasket

1-F4TZ6A636A Gasket

Save buying this kit vs indiviual pieces

Geat New Year Price!

You will recieve the all of the following. A complete kit to add the Factory Upfitter bank of switches to run whatever accessories you like onto your 2008.

1- bank of On/Off switches fits into existing panel on dash no cutting or drilling required.

1- Complete harnes with plugs to plug right into the fuse panel, you also get all of the necessary relays and fuses installed in the block which is integrated into the harness.

1- Storage bin to fill the gap right after installing switches on some applications.

Click here to see an installation of our Upfitter switch kit.